Modeling Alcohol Dehydrogenase Catalysis in Deep Eutectic Solvent/Water Mixtures

The use of oxidoreductases (EC1) in non-conventional reaction media has been increasingly explored. In particular, deep eutectic solvents (DESs) have emerged as a novel class of solvents. Herein, an in-depth study of bioreduction with an alcohol dehydrogenase (ADH) in the DES glyceline is presented. The activity and stability of ADH in mixtures of glyceline/water with varying water contents were measured. Furthermore, the thermodynamic water activity and viscosity of mixtures of glyceline/water have been determined. For a better understanding of the observations, molecular dynamics simulations were performed to quantify the molecular flexibility, hydration layer, and intraprotein hydrogen bonds of ADH. The behavior of the enzyme in DESs follows the classic dependence of water activity (a_W) in non-conventional media. At low a_W values (<0.2), ADH does not show any activity; at higher a_W values, the activity was still lower than that in pure water due to the high viscosities of the DES. These findings could be further explained by increased enzyme flexibility with increasing water content.     

Development of LTCC micro-hotplate with PTC temperature sensor for gas-sensing applications

Low temperature co-fired ceramic (LTCC) micro-hotplates show wide applications in gas sensors and micro-fluidic devices. It is easily structured in three-dimensional structures. This paper presents the low power consumption micro-hotplates which were developed with PTC (positive temperature coefficient) temperature sensor and inter-digitated electrodes. The paper presents two different structures for micro-hotplate with platinum as a heating element. The PTC temperature sensor using two different materials viz. PdAg and platinum paste are developed with micro-hotplates. The simulation has been achieved through COMSOL for LTCC and alumina micro-hotplates. The temperature variation with power consumption has been measured for the developed LTCC micro-hotplates. The change in resistance of PTC temperature sensors was measured with micro-hotplate temperature. The aim of this study was to place a temperature sensor with the gas sensor module to measure and control the temperature of micro-hotplate. A SnO₂ sensing layer is coated on LTCC micro-hotplate using screen printing and characterized for the sensing of carbon monoxide gas (CO). This study will be beneficial for designing hotplates based on LTCC technology with low power consumption and better stability of temperature for gas-sensing applications.     

A cathode support structure for use in a magnetron oscillator experiment

A low temperature co-fired ceramic (LTCC) material system has been used to develop a protype field emission cathode structure for use in an experimental magnetron oscillator. The structure is designed for used with 30 gated field emission array (GFEA) die electrically connected through silver metal traces and electrical vias. To approximate a cylinder, the cathode structure (48 mm long and 13.7 mm in diameter) is comprised of 10 faceted plates which cover the GFEA dies. Slits in the facet plates allow electron injection. The GFEA die (3 mm × 8 mm) are placed in axial columns of 3 and spaced azimuthally around a cylindrical support structure in a staggered configuration resulting in 10 azimuthal locations. LTCC manufacturing techniques were developed in order to fabricate the newly designed cathode with seven layers wrapped to form the cylinder with electrical traces and vias. Two different cathode wrapping techniques and two different via filling techniques were studied and compared. Two different facet plate manufacturing techniques were studied. Finally, four different support stand configurations for firing the cylindrical structure were also compared with a square post stand having the best circularity and linearity measurements of the fired structure.     

高温气冷堆舱室抗商用飞机撞击的耦合数值分析

本文建立了大型商用飞机撞击典型高温气冷堆核电站反应堆舱室的非线性有限元模型，计算中混凝土舱室直接采用工程用钢筋混凝土的损伤塑性本构模型，飞机结构采用Johnson-Cook本构模型。对飞机高速撞击高温气冷堆核电站反应堆舱室非线性撞击过程进行模拟计算，得出正面和侧面撞击条件下的撞击载荷曲线、撞击位移云图、反应堆舱室混凝土破坏情况等结果。评估表明，反应堆舱室结构在撞击条件下的整体损伤微小，可为保护内部关键设备提供重要的屏障功能。     

温拌LDPE改性沥青混合料性能研究

选择Sasobit和Evotherm 3G两种温拌剂对温拌LDPE沥青混合料制备工艺和性能进行研究。首先,比较变温等体积法和等黏温度法两种方法,并确定两种温拌混合料的拌和及击实温度。在此基础上,分别采用车辙试验、低温弯曲试验、中点加载弯曲试验以及冻融劈裂试验评价70#、LDPE、Sasobit-LDPE以及3G-LDPE四种沥青混合料的高温性能、低温性能、疲劳性能和水稳定性。结果表明,两种温拌技术均是可行的,Sasobit和3G温拌技术可使施工温度降低20℃和15℃。与热拌LDPE沥青混合料相比,Sasobit温拌沥青混合料具有更好的高温性能和水稳定性,在高应力比条件下抗疲劳性能更好,低温性能虽变差,但是优于70#沥青混合料;3G温拌沥青混合料的高温性能,低温性能以及水稳定性则与热拌LDPE沥青混合料各项性能较为接近,抗疲劳性能变差,但是优于70#沥青混合料。     

On the thermal conductivity of bimodal SiC/A356 composites fabricated via powder metallurgy route

The present study investigates the thermal conductivity of bimodal SiC particulate distribution in aluminum matrix composites fabricated via powder metallurgy route. The effects of the SiC_p reinforcement size distribution and processing parameters such as sintering time and temperature on the thermal conductivity have been examined. The Box–Behnken experimental array was employed to identify the effects of selected variables on the thermal conductivity of the composite. A reasonable augmentation in the thermal conductivity was observed with an increase in sintering time and %volume fraction of fine SiC particulates. It has been demonstrated that the matrix doped with fine SiC particulates (37?µm) occupied interstitial positions and formed continuous SiC–matrix network resulting in minimizing the micropores that contributed for good thermal conductivity, that is, 235?W/mK. Scanning electron microscopy (SEM) and x-ray diffraction (XRD) were conducted to evaluate the microstructure architecture and interfacial phase formation.     

Study on migration characteristics of heavy metals during oil sludge incineration

Experimental and simulation studies on the migration characteristics of heavy metals during the incineration of OS were conducted with a tube furnace reactor and thermodynamic equilibrium calculation software FactSage, respectively. The results showed that when the incineration temperature increased from 800°C to 1100°C, the release rates of heavy metals such as Cr, Pb, Cu, Zn and Ni increased gradually and reached the maximum at 1000°C. When the excess air ratio increased from 1.0 to 1.4, the release rates of heavy metals such as Cr, Pb, Cu, Zn and Ni first decreased and then became steady. The content of gaseous hydroxide of Cr and gaseous chlorides of Pb and Cu increased while the chemical forms of Zn and Ni did not change obviously with the increase of combustion temperature or excess air ratio.     

Automatic Transformation of Membrane‐Type Electronic Devices into Complex 3D Structures via Extrusion Shear Printing and Thermal Relaxation of Acrylonitrile–Butadiene–Styrene Frameworks

This work demonstrates a means of automatic transformation from planar electronic devices to desirable 3D forms. The method uses a spatially designed thermoplastic framework created via extrusion shear printing of acrylonitrile–butadiene–styrene (ABS) on a stress‐free ABS film, which can be laminated to a membrane‐type electronic device layer. Thermal annealing above the glass transition temperature allows stress relaxation in the printed polymer chains, resulting in an overall shape transformation of the framework. In addition, the significant reduction in the Young's modulus and the ability of the polymer chains to reflow in the rubbery state release the stress concentration in the electronic device layer, which can be positioned outside the neutral mechanical plane. Electrical analyses and mechanical simulations of a membrane‐type Au electrode and indium gallium zinc oxide transistor arrays before and after transformation confirm the versatility of this method for developing 3D electronic devices based on planar forms.     

The control of paracetamol particle size and surface morphology through crystallisation in a spray dryer

The parameters governing the crystallisation of paracetamol using various conventional techniques has been extensively studied, however the factors influencing the drug crystallisation using spray drying is not as well understood. The aim of this work was to investigate the crystallisation of an active pharmaceutical ingredient through evaporative crystallisation using a spray dryer to study the physicochemical properties of the drug and to use semi-empirical equations to gain insight into the morphology and particle size of the dried powder. Paracetamol solutions were spray dried at various inlet temperatures ranging from 60 °C to 120 °C and also from a series of inlet feed solvent compositions ranging from 50/50% v/v ethanol/water to 100% ethanol and solid-state characterisation was done. The size and morphology of the dried materials were altered with a change in spray drying parameters, with an increase in inlet temperature leading to an increase in particle Sauter mean diameter (from 3.0 to 4.4 µm) and a decrease in the particle size with an increase in ethanol concentration in the feed (from 4.6 to 4.4 µm) as a result of changes in particle density and atomised droplet size. The morphology of the dried particles consisted of agglomerates of individual crystallites bound together into larger semi-spherical agglomerates with a higher tendency for particles having crystalline ridges to form at higher ethanol concentrations of the feed.     

P91钢管道异常低硬度部位的组织和性能

对电厂运行过程中发现的P91钢主蒸汽管道的低硬度部位进行了微观组织观察、短时力学性能试验和高温持久强度试验,分析了其硬度偏低的原因。结果表明,低硬度区域P91钢组织为铁素体+析出物,位错密度较低,M₂₃C₆相在晶界处粗化聚集,同时析出新相Laves相,使得P91钢的短时力学性能和高温持久强度下降严重。